Viega - Seite 26

Viega 3090

Flow-optimised press connector system for drinking water installations in acc. with DIN 1988 and DIN 50930-6 as well as heating installations, tested in acc. with DVGW worksheet W 534.Press connectorsSafe and fast processing without calibration of the pipe ends through O-ring-free press technology in all dimensions. In this way, widening or calibration of the pipe-ends becomes superfluous and reduces the assembly times. The interaction between aerodynamic radii and minimal cross-section narrowings ensure the lowest pressure losses in press systems for multilayer pipes. This allows a smaller dimensioning of drinking water installations and reduces the pipeline volume.SC-ConturAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionPipesRaxofix PE-Xc/Al/PE-Xc•dimensionally stable, oxygen-proof in acc. with DIN 4726, greyRaxofix PE-Xc•flexible, blackDimensionsPress connectors and pipes•Raxofix-PE-Xc/Al/PE-Xc: d 16/20/25/32/40/50/63•Raxofix PE-Xc: d 16/20Areas of application PE-Xc/Al/PE-XcDrinking waterHeatingRainwaterCompressed airAreas of application PE-XcRainwaterDrinking waterUse of the system for application areas other than those described here must be agreed with Viega Service Center.Operating conditionsDrinking water installations•Operating temperature max. 70 °C•Operating pressure max. 1.0 MPaHeating installations•Operating temperature max. 80 °C•Operating pressure max. 1.0 MPaIrrelevant of the direction of flow, mixed installations are permitted.NoteThe DVGW test mark is only valid f

Langer Nippel in Waffengrau mit R-Gewinde. R: 34, L: 200 mm

Raxofix Adapter mit SC-Contur-Silicium-Bronze-Pressanschluss, Rp-Gewinde: 32, Rp: 1

Viega 2316

Viega 1111

Viega awkward connection pipe with eccentric sleeve, for tolerance compensation for toilet drain connection, with lip seal.

Universal valve with stainless steel valve upper part, with plug, plastic valve lower part, silver-coloured.

Screw fitting- gunmetal or silicon bronze- R-thread, Rp-thread- flat sealing, angled

Sanpress Plug-in piece- gunmetal or silicium bronze- plug-in end, R-threadComponentsPolygon.

Long nipple- gunmetal- R-thread

Long nipple- gunmetal- R-thread

Long nipple- gunmetal- R-thread

Viega 2612

Viega 2211XL

Sanpress Inox Plug-in piece- steel non-corroding- plug-in end, Rp-threadComponentsPolygon d: 15, Rp: 12

Sanpress Inox Plug-in piece- steel non-corroding- plug-in end, R-threadComponentsPolygon d: 28, R: 1

Pressverbindungssystem mit Pressverbindern aus Kupfer und Rotguss, geprüft gemäß DVGW-Arbeitsblatt W 534 mit DVGW-Prüfsiegel und Rohren aus Kupfer gemäß EN 1057 in Übereinstimmung mit dem DVGW-Arbeitsblatt GW 392. Geeignet für Trinkwasserinstallationen gemäß DIN 1988. Für dimensionsstabile verdeckte und Vorwandinstallationen von Sammel- und Steigleitungen im Viega-Komponentensystem. Pressverbinder Alle Größen mit SC-Contur - Verbindungen, die ungedrückt bleiben, werden sichtbar, wenn das System gefüllt ist. Der SC-Contur ist zertifiziert und erfüllt die Anforderungen des DVGW-Arbeitsblatts W 534, Punkt 12.14, Verbindungen mit Zwangsleckage. Bei Dichtheitsprüfungen mit Wasser garantiert Viega die Identifizierung ungedrückter Verbindungen im Druckbereich von 0,1 MPa bis 0,65 MPa; bei einer trockenen Dichtheitsprüfung mit Druckluft oder Edelgasen von 22 hPa bis zu einem Druck von maximal 0,3 MPa.MarkingGreen dot on the press connectionSealing elementsEPDM (Ethylen-Propylen-Dien-Monomer-Kautschuk), schwarz bis zu einer Temperatur von 110 °C

Viega 2218XL

Long nipple- gunmetal- R-thread

Viega 3240

Press connector system with press connectors and pipes made of stainless steel material Nos. 1.4401 and 1.4521 in acc. with DIN EN 10088, DIN EN 10312, DVGW worksheet GW 541, system certification for connectors and pipes in acc. with DVGW worksheet W 534, for drinking water installations in acc. with DIN 1988. For dimensionally stable concealed and pre-wall installations of manifold and riser pipes in Viega component assembly.Press connectorsAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionSealing elementsEPDM, black (ethylene-propylene-die

Stecker- Gunmetal- R-GewindekomponentenQuadraticR: 14

Langer Nippel- Gunmetal- R-Gewinde: 34, L: 50

Adapter - Gunmetal - gelötete Verbindung, R-Gewinde: 22, R: 12