PEX-Systeme - Seite 9

Uponor 1001231 Sanitärarmatur Kompressionskrümmung

Uponor 1008684 Sanitärarmatur Armaturenanschluss

Uponor 1008661 Sanitärarmatur Armaturenanschluss

HENCO VISION 26 mm Adapterhülse für Verteiler für Wasser-, Heizungs- und Kühlanlagen Max. 16 bar

Uponor 1033974 Sanitärarmatur Endzufuhrbiegung

HENCO VISION end plug for manifolds for water, heat and electricity installations Max. 16 bar

Used for QuickBox.

HENCO VISION connection part to the manifold, angle 26 mm for water, heating and cooling installations Max. 16 bar

Used for Roth Quickskab, manifold cabinet

Used for Pex and CU pipe

Manifold in gunmetal with push and insert in AISI 316

Wallofix Installationswerkzeug zur Markierung der Einstecktiefen und Montage sowie Montage in der Ebene mit einem Mittelabstand

Werkzeug für Flansch an der Wand

WALLOFIX Flansch für Membran zur Wanddose

Fitting in gunmetal for Roth manifold

Manifold in gunmetal with push and insert in AISI 316

EPDM 120x120 - ø54

Aufhängeclips für PPM-Verteiler zur Montage im Verteilerschrank. Hergestellt aus PPSU.

Flow-optimised press connector system for drinking water installations in acc. with DIN 1988 and DIN 50930-6 as well as heating installations, tested in acc. with DVGW worksheet W 534.Press connectorsSafe and fast processing without calibration of the pipe ends through O-ring-free press technology in all dimensions. In this way, widening or calibration of the pipe-ends becomes superfluous and reduces the assembly times. The interaction between aerodynamic radii and minimal cross-section narrowings ensure the lowest pressure losses in press systems for multilayer pipes. This allows a smaller dimensioning of drinking water installations and reduces the pipeline volume.SC-ConturAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionPipesRaxofix PE-Xc/Al/PE-Xc•dimensionally stable, oxygen-proof in acc. with DIN 4726, greyRaxofix PE-Xc•flexible, blackDimensionsPress connectors and pipes•Raxofix-PE-Xc/Al/PE-Xc: d 16/20/25/32/40/50/63•Raxofix PE-Xc: d 16/20Areas of application PE-Xc/Al/PE-XcDrinking waterHeatingRainwaterCompressed airAreas of application PE-XcRainwaterDrinking waterUse of the system for application areas other than those described here must be agreed with Viega Service Center.Operating conditionsDrinking water installations•Operating temperature max. 70 °C•Operating pressure max. 1.0 MPaHeating installations•Operating temperature max. 80 °C•Operating pressure max. 1.0 MPaIrrelevant of the direction of flow, mixed installations are permitted.NoteThe DVGW test mark is only valid f

Termination box, including termination elbow in DR-brass and mounting screws. For water proof connection with PE-Xa pipes and Uponor conduit in all types of walls, according to NT VVS 129.

Vereinige einzelne, schwarze mit Druckverschraubungen mit 15 mm PEX/P.E.R.T. Getestet für den Einsatz in feuchten Bereichen. Der Wandanschluss passt zu 15x2,5 PEX und 20/25 gewellten Rohren. Der Messingteil besteht aus Bronze und ist für Trinkwasser zugelassen. Der Kunststoffteil besteht aus PE.

Montagehalterung Uponor Smart Aqua plus M7

Used for replacement of Roth Pipe in 15 mm

HENCO VISION Gunmetal-Hülsenadapter 20 x 3/4 für Verteilerrohre für Wasser-, Heizungs- und Kühlanlagen Max. 16 bar

Rohrschneider bis 22mm, Unite.