PEX-Systeme - Seite 8

Quickbox tool for flange

Manifold for water TEA 3 outlets 16/12 mm fittings

Transition from 15 mm to pipe thread.

Hergestellt von PPSU. Q&E-System nur mit Uponor PE-Xa Rohren verwenden

TEE M/FITTING Q&E PPSU UPONOR 16X1/2X16 mm

Adapter für die Verwendung mit dem PPM-Verteilersystem. Maximaler Druck: 10 bar Maximale Temperatur: 70°C Die Montage des Adapters und des Verteilers erfolgt ohne Werkzeug mit einer Bajonettkupplung.

End cap ppm Uponor 1

Pressanschluss 15 mm x 12

Manifold for water TEA 2 outlets 16/12 mm fittings

Messingkappe für Krümmer. Mit TEA-Oberfläche.

Transition from 22 mm to pipe thread.

For assembly of pipes or fittings.

Uponor 3/4 4X15 mm Rohr mit fester Buchse

Used for connection between Pex and pipe, valves etc. with thread

Plaserboard kit to wallbox

Uponor 20 mm Rohrhalterung.

For assembly of pipes or fittings.

HENCO VISION 20 mm Adapterhülse für Verteiler für Wasser-, Heizungs- und Kühlanlagen Max. 16 bar

Used in dry wall to Roth QuickBox, when the installation is extraordinarily deep.

To shorten the length of the QuickBox

Flow-optimised press connector system for drinking water installations in acc. with DIN 1988 and DIN 50930-6 as well as heating installations, tested in acc. with DVGW worksheet W 534.Press connectorsSafe and fast processing without calibration of the pipe ends through O-ring-free press technology in all dimensions. In this way, widening or calibration of the pipe-ends becomes superfluous and reduces the assembly times. The interaction between aerodynamic radii and minimal cross-section narrowings ensure the lowest pressure losses in press systems for multilayer pipes. This allows a smaller dimensioning of drinking water installations and reduces the pipeline volume.SC-ConturAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionPipesRaxofix PE-Xc/Al/PE-Xc•dimensionally stable, oxygen-proof in acc. with DIN 4726, greyRaxofix PE-Xc•flexible, blackDimensionsPress connectors and pipes•Raxofix-PE-Xc/Al/PE-Xc: d 16/20/25/32/40/50/63•Raxofix PE-Xc: d 16/20Areas of application PE-Xc/Al/PE-XcDrinking waterHeatingRainwaterCompressed airAreas of application PE-XcRainwaterDrinking waterUse of the system for application areas other than those described here must be agreed with Viega Service Center.Operating conditionsDrinking water installations•Operating temperature max. 70 °C•Operating pressure max. 1.0 MPaHeating installations•Operating temperature max. 80 °C•Operating pressure max. 1.0 MPaIrrelevant of the direction of flow, mixed installations are permitted.NoteThe DVGW test mark is only valid f

Transition from 18 mm to pipe thread.

Uponor 1001231 Sanitärarmatur Kompressionskrümmung

Uponor 1008684 Sanitärarmatur Armaturenanschluss

Used for connection between Pex and pipe, valves etc. with thread