PEX-Systeme - Seite 7

Manifold cabinet for Roth floorheating manifold

Transition from 18 mm to pipe thread.

Fitting in gunmetal for Roth manifold

For 2 pipe, in 15 mm

Isolierung für Uponor Aqua PLUS Verteiler. Set mit Isolierung, 10 Auslässen und zwei Endabdeckungen.

Roth Quickbox drain system watertight cabinets.

Flow-optimised press connector system for drinking water installations in acc. with DIN 1988 and DIN 50930-6 as well as heating installations, tested in acc. with DVGW worksheet W 534.Press connectorsSafe and fast processing without calibration of the pipe ends through O-ring-free press technology in all dimensions. In this way, widening or calibration of the pipe-ends becomes superfluous and reduces the assembly times. The interaction between aerodynamic radii and minimal cross-section narrowings ensure the lowest pressure losses in press systems for multilayer pipes. This allows a smaller dimensioning of drinking water installations and reduces the pipeline volume.SC-ConturAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionPipesRaxofix PE-Xc/Al/PE-Xc•dimensionally stable, oxygen-proof in acc. with DIN 4726, greyRaxofix PE-Xc•flexible, blackDimensionsPress connectors and pipes•Raxofix-PE-Xc/Al/PE-Xc: d 16/20/25/32/40/50/63•Raxofix PE-Xc: d 16/20Areas of application PE-Xc/Al/PE-XcDrinking waterHeatingRainwaterCompressed airAreas of application PE-XcRainwaterDrinking waterUse of the system for application areas other than those described here must be agreed with Viega Service Center.Operating conditionsDrinking water installations•Operating temperature max. 70 °C•Operating pressure max. 1.0 MPaHeating installations•Operating temperature max. 80 °C•Operating pressure max. 1.0 MPaIrrelevant of the direction of flow, mixed installations are permitted.NoteThe DVGW test mark is only valid f

Mehrfachverteiler für Wasser mit 2 Auslässen. Inklusive 15 mm Anschluss für Polyethylenrohr mit TEA-Oberfläche.

For Roth gunmetal manifold

Slip coupling, push-fit 18mm stainless steel

Fits directly into insertion fitting.

HENCO Druckprüfstopfen 26 mm für Wasser-, Heizungs- und Elektroinstallationen Max. 16 bar

HENCO VISION PVDF transition 15 x 3/4 from distribution pipes for water, heating and cooling installations Max. 16 bar

HENCO VISION 3-Wege-Verteilerrohre für Wasser-, Heizungs- und Elektroinstallationen Max. 16 bar

Extra breite Metallhalterung für Uponor Anschlussdosen mit Schraublöchern (D4 mm) - c/c 150 mm. Höhe 70 mm, Breite 360 ​​mm, Dicke 1,25 mm. Zur Installation in Beton, Leichtbeton und Plattenwand. Kann von vorne und hinten an einer Wand montiert werden.

Backplate elbow is used in e.g. utility room.

Fits directly into insertion fitting.

Fits directly into insertion fitting.

Slip coupling, push-fit 15mm stainless steel

For assembly of pipes or fittings.

Slip coupling, push-fit 22mm stainless steel

For assembly of pipes or fittings.

Wasserdichte Anschlussdose für flexibles Polybuten - nicht geeignet für PE-X / AI / PE-X, PE-Xc - Rotguss - Rp-Gewinde - Schalldämmung. Mit Winkel aus Rotguss und Druckprüfdüse. Modell 5330

HENCO VISION gunmetal sleeve adapter 20 x 1/2 to distribution pipes for water, heating and cooling installations Max. 16 bar

Wallbox for Pex