PEX-Systeme - Seite 5

Messingverteiler mit 3 Auslässen für Wasser- und Heizsysteme.

Mehrfachverteiler aus DR Messing. Mit Druckfittings geliefert.

Roth manifold in gunmetal for pex pipe

Flow-optimised press connector system for drinking water installations in acc. with DIN 1988 and DIN 50930-6 as well as heating installations, tested in acc. with DVGW worksheet W 534.Press connectorsSafe and fast processing without calibration of the pipe ends through O-ring-free press technology in all dimensions. In this way, widening or calibration of the pipe-ends becomes superfluous and reduces the assembly times. The interaction between aerodynamic radii and minimal cross-section narrowings ensure the lowest pressure losses in press systems for multilayer pipes. This allows a smaller dimensioning of drinking water installations and reduces the pipeline volume.SC-ConturAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpresse

Transition from 15 mm to pipe thread.

Transition from 22 mm to pipe thread.

Terminationsbox, einschließlich Q&E PPSU Abschlussbogen, weißem Q&E Ring und Montageschrauben. Für wasserdichte Verbindungen mit PE-Xa Rohren und Uponor Leitungen in allen Arten von Wänden gemäß NT VVS 129.

Vorteile von Uponor Rohr 3/4 3X15 mm mit fester Steckdose.

Flow-optimised press connector system for drinking water installations in acc. with DIN 1988 and DIN 50930-6 as well as heating installations, tested in acc. with DVGW worksheet W 534.Press connectorsSafe and fast processing without calibration of the pipe ends through O-ring-free press technology in all dimensions. In this way, widening or calibration of the pipe-ends becomes superfluous and reduces the assembly times. The interaction between aerodynamic radii and minimal cross-section narrowings ensure the lowest pressure losses in press systems for multilayer pipes. This allows a smaller dimensioning of drinking water installations and reduces the pipeline volume.SC-ConturAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionPipesRaxofix PE-Xc/Al/PE-Xc•dimensionally stable, oxygen-proof in acc. with DIN 4726, greyRaxofix PE-Xc•flexible, blackDimensionsPress connectors and pipes•Raxofix-PE-Xc/Al/PE-Xc: d 16/20/25/32/40/50/63•Raxofix PE-Xc: d 16/20Areas of application PE-Xc/Al/PE-XcDrinking waterHeatingRainwaterCompressed airAreas of application PE-XcRainwaterDrinking waterUse of the system for application areas other than those described here must be agreed with Viega Service Center.Operating conditionsDrinking water installations•Operating temperature max. 70 °C•Operating pressure max. 1.0 MPaHeating installations•Operating temperature max. 80 °C•Operating pressure max. 1.0 MPaIrrelevant of the direction of flow, mixed installations are permitted.NoteThe DVGW test mark is only valid f

Polyethylene insulation for Pettinaroli utility water distribution pipe CC50. Fits 4 circles and can be easily cut as needed.Note: can only be used for CC50 and not CC35.

Hergestellt aus Polypropylen. Für Bodendurchführungen für Heizkörper. Passt in leere Rohre mit Abmessungen von 25/20. C/C 40 mm. Kann mit einem Abstandshalterblock modifiziert werden.

Used for connection between Pex/Alu and pipe, valves etc. with thread

Backplate elbow is used in e.g. utility room.

For assembly of pipes or fittings.

Support bushes for Pex and insert fittings.

The QuickBox fitting is used under sinks with the option of connecting a tap, dishwasher, etc.

Tool for fix of floorheating pipe

Used for Pex and CU pipe

Used for Roth gunmetal manifold

PPM modulares Verteilersystem für Trinkwasser aus PPSU (Polyphenylsulfon) mit Bajonett-Adaptern für mehrere Anschlüsse. Maximaler Druck: 10 bar, maximale Temperatur: 70 °C

Schiene für PEX wird für PEX-Rohre und Fußbodenheizung vor dem Gießen verwendet. Mitteabstand: 50 mm. Inklusive Trennung und 2 separaten Rohren.

Used for pexpipe

For assembly of pipes or fittings.

Pipe cutter for up to 28 mm

Rohrschelle zur Befestigung von Rohren, 25mm. UniteSchrauben inklusive