Entwässerungsprodukte - Seite 34

For shower cubicles with open right-hand side, glass screen or similar.

The drain unit has two wall flanges.

The Wafix PP system is made from the reusable PP (Polypropylene), which gives both pipes and fittings good physical and chemical properties. The PP material used has a high E-module, which gives the pipes a good length stiffness and a great impact strength. Therefore, the Wafix PP system withstands the impacts and shocks that can occur during installation and operation - even at minus degrees. Wafix PP is a complete drainage system with pipes and fittings in the dimensions: Ø32 mm Ø40 mm Ø50 mm Ø50 mm Ø75 mm Ø110 mm The program also comes in a white version in dimensions Ø32, Ø40 and Ø50 mm, especially suitable for visible installations. The system's unique Fix·lock® sealing ring seals on as many as three points, providing a large construction surface against the pipe and ensuring that your joints are 100% dense each time. It provides extra security and security if you insert or hide the pipes in a shaft.

Stücke aus PEH zum Schweißen werden für Abwasserinstallationen verwendet. Mit TPE-Schalldämpfung.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Has an automatic odour barrier instead of a water trap, so that it cannot dry out. The odour barrier can be removed for cleaning. VA-approved.

– Should not be used in multi-storey buildings
– The odour barrier may react to over-pressure and under-pressure in the drain system
– Correct ventilation of the drain system is important
– The odour barrier opens and closes with the help of a spring
– A rubber seal ensures that the odour barrier is closed when not in use

Wavin PP sewer pipe 110x500mm SN4 EN13476

Eine weiße runde Platte mit einem Durchmesser von 150 mm.

Membrane JO

Wastewater pipesystem GM-X galvanized DN 70x1000 mm

Geberit Elektroschweißband für Ankerpunkt: D=125 mm

double slip coupling 110mm ss/316

Abwasserrohrsystem GM-X, verzinkt, gebogen DN 50, 87 Grad

Geberit Doppelkammerfalle für Küchenspülen, mit abgewinkeltem Schlauchanschluss, vertikalem Auslass: d50mm G1 1/2 weiß alpin

Für Gebäudeentwässerung, für Geländeentwässerung

Stücke aus PEH zum Schweißen werden für Abwasserinstallationen verwendet. Mit TPE-Schalldämpfung.

Drain bowl Purus with stainless steel grate 50 mm.

Outlet-Einheit | Leitung | Ø 50 mm horizontal, inkl. Siphon

Outlet-Haus Unidrain Ø75 horizontal mit Wassersperre.

Wechsel von Jo-Flex 11/4 Nippel auf 40 mm.

Abflussgarnitur Unidrain 1001, 1200 mm.

The water trap is removable and can be taken apart for cleaning.

Note: The outlet unit can be used in 3 different ways:
– If the water trap is positioned at the top and the top two side spigots are used as inlets from an external unit, then a separate water trap must be installed on the added unit.
– If the water trap is pushed down into the outlet unit, the external unit connected to the top side spigots will be covered by the included water trap, so there is no need for an external water trap.
– If the bottom two side inlets are used, you must establish an external water trap, regardless of the position of the Unidrain water trap.

The grating is placed on a countersunk bearing in the frame, to hold it securely.

Only for use with ClassicLine frame.

The set consists of a panel, rail, heightener set and screws. The set must be assembled before installation.

Includes 2 x hooks to be used for lifting the panel.

The panel solution is placed directly inside the drain unit.

The rail is specially designed to provide a snug fit. Installed with HighLine frame.

The heightener set to adjust the panel is included, so that the panel can be matched to the frame height.

The water trap is removable and can be taken apart for cleaning

Note: The outlet unit can be used in 3 different ways:
– If the water trap is positioned at the top and the top two side spigots are used as inlets from an external unit, then a separate water trap must be installed on the added unit.
– If the water trap is pushed down into the outlet unit, the external unit connected to the top side spigots will be covered by the included water trap, so there is no need for an external water trap.
– If the bottom two side inlets are used, you must establish an external water trap, regardless of the position of the Unidrain water trap.

Available in 8, 10 and 12 mm heights (depending on the thickness of the floor tile).

The rubber insert ensures a snug fit inside the unit. A countersunk bearing ensures that the grating fits perfectly into the frame.

The frame is non-optional and has two functions: To support the grating and give a perfectly flush finish with the tiled floor.

The grating is selected from among six attractive designs.

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.