Alu pex Systeme - Seite 10

Flow-optimised press connector system for drinking water installations in acc. with DIN 1988 and DIN 50930-6 as well as heating installations, tested in acc. with DVGW worksheet W 534.Press connectorsSafe and fast processing without calibration of the pipe ends through O-ring-free press technology in all dimensions. In this way, widening or calibration of the pipe-ends becomes superfluous and reduces the assembly times. The interaction between aerodynamic radii and minimal cross-section narrowings ensure the lowest pressure losses in press systems for multilayer pipes. This allows a smaller dimensioning of drinking water installations and reduces the pipeline volume.SC-ConturAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionPipesRaxofix PE-Xc/Al/PE-Xc•dimensionally stable, oxygen-proof in acc. with DIN 4726, greyRaxofix PE-Xc•flexible, blackDimensionsPress connectors and pipes•Raxofix-PE-Xc/Al/PE-Xc: d 16/20/25/32/40/50/63•Raxofix PE-Xc: d 16/20Areas of application PE-Xc/Al/PE-XcDrinking waterHeatingRainwaterCompressed airAreas of application PE-XcRainwaterDrinking waterUse of the system for application areas other than those described here must be agreed with Viega Service Center.Operating conditionsDrinking water installations•Operating temperature max. 70 °C•Operating pressure max. 1.0 MPaHeating installations•Operating temperature max. 80 °C•Operating pressure max. 1.0 MPaIrrelevant of the direction of flow, mixed installations are permitted.NoteThe DVGW test mark is only valid f

Used with Roth alu-laserplus pipe and Roth tools

PPSU-Bogen Uponor 90° 40X40 mm

Geberit Mepla T-piece, reduced: d=20mm, d1=16mm, d2=16mm

Geberit Mepla T-Stück, reduziert: d=26mm, d1=26mm, d2=20mm

Used with Roth alu-laserplus pipe and Roth tools

Raxofix T-Stück mit SC-Contur- Siliziumbronze-Pressverbindern d1: 32, d2: 32, d3: 32

Raxofix T-Stück mit SC-Contur- Siliciumbronze-Pressverbindern d1: 25, d2: 20, d3: 25

Used with Roth alu-laserplus pipe and Roth tools

Uponor 1070524 Sanitärarmatur Elbow

Used with Roth alu-laserplus pipe and Roth tools

Used with Roth alu-laserplus pipe and Roth tools

Raxofix T-Stück mit SC-Contur- Siliciumbronze-Pressverbindern d1: 20, d2: 20, d3: 16

Raxofix Verbindungsschraubfitting mit SC-Contur- Siliziumbronze- Pressanschluss, G-Gewinde- Flachdichtungskomponenten EPDM-Dichtelement d: 16, G: 34

Raxofix T-Stück mit SC-Contur- Siliciumbronze-Pressverbindern d1: 16, d2: 16, d3: 16

Raxofix Verbindungsschraubfitting mit SC-Contur für Verteiler aus Siliziumbronze mit Pressanschluss, Viega Steckplatz: 16, G: 34

Raxofix Adapterbogen 90° mit SC-Contur-Siliziumbronze-Presseanschluss, R-Gewinde: 20, R: 12

Uponor 1070504 Sanitärarmatur Armaturenanschluss

Uponor 1070503 Sanitärarmatur Armaturenanschluss

Used with Roth alu-laserplus pipe and Roth tools

PPSU-Kupplung Uponor 40X32 mm

Press coupling for DHW and radiator systems. PPSU plastic with stainless steel/aluminum press cap, guaranteed leaking if not pressed. Calibration-free. Only to be used with Uponor MLC tubes and with Uponor approved pressing tools.

Prestee PPSU Uponor 32X20X32 mm

Geberit Mepla Adapter mit Innengewinde: d=16mm, Rp=1/2

45° Presbend PPSU Uponor 50 x 50 mm.