Long nipple- gunmetal- R-threadR: 34, L: 100

Coupling- gunmetal- Rp-threadRp: 12

Cap- gunmetal- Rp-threadComponentsPolygonRp: 12

Fittings with threads in acc. with DINEN 10226, Part 1, certified for drinking water in acc. with DIN 1988 and gas installations in acc. with TRGI 2008 (observe notes on the model), tested in acc. with DVGW worksheet GW 6 and GW 393.CertificatesGunmetal threaded fittings – DVGW-Reg.-No. DV-7401AO2957Threaded connectionsR-external thread, produced on site – hempen without roughening of the thread is possible.

Fittings with threads in acc. with DINEN 10226, Part 1, certified for drinking water in acc. with DIN 1988 and gas installations in acc. with TRGI 2008 (observe notes on the model), tested in acc. with DVGW worksheet GW 6 and GW 393.CertificatesGunmetal threaded fittings – DVGW-Reg.-No. DV-7401AO2957Threaded connectionsR-external thread, produced on site – hempen without roughening of the thread is possible.

Reducer- gunmetal- R-thread, Rp-thread- roundR: 12, Rp: 1

Viega 3241

Reducer- gunmetal- R-thread, Rp-thread- roundR: 12, Rp: 34

Plug- gunmetal- R-threadComponentsQuadraticR: 34

Reducer- gunmetal- R-thread, Rp-threadComponentsPolygonR: 2, Rp: 112

Coupling- gunmetal- Rp-threadRp: 2

Viega 3241

Viega 2618

Viega 2615.1

Viega 2226.1

Viega 2218

Press connector system with press connectors made of gunmetal, pipes made of stainless steel material Nos. 1.4401 and 1.4521 in acc. with DINEN 10088, DIN EN 10312, DVGW worksheet GW 541, system certification for connectors and pipes in acc. with DVGW worksheet W 534, for drinking water installations in acc. with DIN 1988. For dimensionally stable concealed and pre-wall installations of manifold and riser pipes in Viega component assembly.Press connectorsAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionSealing elementsEPDM, black (ethylene

Sanpress T-piece with SC-Contur- gunmetal or silicium bronze- press connectorsComponentsEPDM sealing elementsd1: 28, d2: 22, d3: 28

Viega 2214.2

Viega 2218

Sanpress T-Stück mit SC-Contur- Gunmetal oder Siliziumbronze- PressverbindernKomponentenEPDM-Dichtelemente d1: 35, d2: 35, d3: 35

Sanpress T-piece with SC-Contur- gunmetal or silicium bronze- press connectors, Rp-threadComponentsEPDM sealing elements, polygon, VdS certificationd1: 35, Rp: 12, d2: 35

Viega 2226

Viega 2214.2

Viega 2218