Flow-optimised press connector system for drinking water installations in acc. with DIN 1988 and DIN 50930-6 as well as heating installations, tested in acc. with DVGW worksheet W 534.Press connectorsSafe and fast processing without calibration of the pipe ends through O-ring-free press technology in all dimensions. In this way, widening or calibration of the pipe-ends becomes superfluous and reduces the assembly times. The interaction between aerodynamic radii and minimal cross-section narrowings ensure the lowest pressure losses in press systems for multilayer pipes. This allows a smaller dimensioning of drinking water installations and reduces the pipeline volume.SC-ConturAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionPipesRaxofix PE-Xc/Al/PE-Xc•dimensionally stable, oxygen-proof in acc. with DIN 4726, greyRaxofix PE-Xc•flexible, blackDimensionsPress connectors and pipes•Raxofix-PE-Xc/Al/PE-Xc: d 16/20/25/32/40/50/63•Raxofix PE-Xc: d 16/20Areas of application PE-Xc/Al/PE-XcDrinking waterHeatingRainwaterCompressed airAreas of application PE-XcRainwaterDrinking waterUse of the system for application areas other than those described here must be agreed with Viega Service Center.Operating conditionsDrinking water installations•Operating temperature max. 70 °C•Operating pressure max. 1.0 MPaHeating installations•Operating temperature max. 80 °C•Operating pressure max. 1.0 MPaIrrelevant of the direction of flow, mixed installations are permitted.NoteThe DVGW test mark is only valid f

Sanpress Inox Sliding coupling with SC-Contur- steel non-corroding- press connectors ComponentsEPDM sealing elementsd: 18

Sanpress Plug-in piece- gunmetal or silicium bronze- plug-in end, R-threadComponentsPolygon d: 15, R: 12

Sanpress Inox Adapter mit SC-Contur-Stahl, nicht korrodierender Pressverbindung, R-Gewindekomponenten EPDM-Dichtelement, Polygon, VdS-Zertifizierung d: 28, R: 34

Sanpress-Kupplung mit SC-Contur- Gunmetal oder Siliziumbronze-PresseanschlüssenKomponentenEPDM-DichtelementeD: 28

Press connector system with press connectors made of gunmetal, pipes made of stainless steel material Nos. 1.4401 and 1.4521 in acc. with DINEN 10088, DIN EN 10312, DVGW worksheet GW 541, system certification for connectors and pipes in acc. with DVGW worksheet W 534, for drinking water installations in acc. with DIN 1988. For dimensionally stable concealed and pre-wall installations of manifold and riser pipes in Viega component assembly.Press connectorsAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionSealing elementsEPDM, black (ethylene

Sanpress Plug-in piece- gunmetal or silicium bronze- plug-in end, R-threadComponentsPolygon d: 22, R: 34

Sanpress Inox Adapter mit SC-Contur-Stahl, nicht korrodierender Pressverbindung, R-Gewindekomponenten EPDM-Dichtelement, Polygond: 15, R: 34

Sanpress Reducer with SC-Contur- gunmetal or silicium bronze- plug-in end, press connectionComponentsEPDM sealing elementd1: 35, d2: 28

Viega 2217.2XL

Viega 2316

Sanpress Inox XL T-Stück mit SC-Contur - Stahl nicht korrodierend - PressverbindernKomponentenEPDM-Dichtungselemente, Schneidringe, Trennringe, VdS-Zertifizierungd1: 76.1, d2: 54, d3: 76.1

Viega 2218

Viega 94243G

Viega 3120

Long nipple- gunmetal- R-thread

Viega 3090

Schraubanschluss- Gunmetal- R-Gewinde, Rp-Gewinde- konische Dichtung

Fittings with threads in acc. with DINEN 10226, Part 1, certified for drinking water in acc. with DIN 1988 and gas installations in acc. with TRGI 2008 (observe notes on the model), tested in acc. with DVGW worksheet GW 6 and GW 393.CertificatesGunmetal threaded fittings – DVGW-Reg.-No. DV-7401AO2957Threaded connectionsR-external thread, produced on site – hempen without roughening of the thread is possible.

Armaturen mit Gewinden gemäß DINEN 10226, Teil 1, zertifiziert für Trinkwasser gemäß DIN 1988 und Gasinstallationen gemäß TRGI 2008 (beachten Sie die Hinweise zum Modell), getestet gemäß DVGW-Arbeitsblatt GW 6 und GW 393. Zertifikate: Rotguss-Gewindefittings - DVGW-Reg.-Nr. DV-7401AO2957 Gewindeverbindungen R-Außengewinde, vor Ort hergestellt - Hanf ohne Vergröberung des Gewindes ist möglich.

Schraubanschluss - Gunmetal - R-Gewinde, Rp-Gewinde - konische Dichtung

Zur Wandmontage, Abwasserschlauch von Waschmaschine oder Geschirrspüler.

Verlängerung - Gunmetal - R-Gewinde, Rp-Gewinde

Kappe zur Einstellung des Rohrgewindes G: 1, Version: weiß

Verlängerung - Gunmetal - R-Gewinde, Rp-Gewinde