Grundfos Pumpen - Seite 3

MAGNA3 65-60 FMAGNA3 – More than a pumpWith its unrivalled efficiency, all-encompassing range and built-in communication capabilities plus functionalities replacing system components, the MAGNA3 is ideal for engineers and specifiers looking to create high-performance systems for buildings. This pump in the Grundfos Master Class will fit both heating and cooling applications perfectly, making it the obvious choice for almost any building project – old or new.The MAGNA3 is of the canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid.The innovative clamp with only one screw enables easy repositioning of the pump head. The MAGNA3 is a pump with no maintenance requirements and with extremely low Life Cycle Cost.The pump is characterised by the following:• controller integrated in the control box• control panel with TFT display on the control box• control box prepared for optional CIM modules• built-in differential-pressure and temperature sensor• cast-iron pump housing (depending on model)• carbon-fibre-reinforced composite rotor can• stainless-steel bearing plate and rotor cladding• aluminium alloy stator housing• air-cooled power electronicsThe MAGNA3 is a single-phase pump.Characteristic features• AUTOADAPT.• FLOWADAPT and FLOWLIMIT (more than a pump function as it reduces the need for pump throttling valves).• Proportional-pressure control.• Constant-pressure control.• Constant-temperature control.• Constant-curve duty.• Max. or min. curve duty.• Automatic Night Setback.• No external motor protection required.• Insulating shells supplied with single-head pumps for heating systems.• Large temperature range where the liquid temperature and the ambient temperature are independent of each other.CommunicationThe MAGNA3 enables communication via the following:• wireless Grundfos GO Remote

Die ALPHA2 ist in der Lage, den harten Bedingungen in einem Heizsystem standzuhalten, und mit vier neu hinzugefügten Funktionen wurde sie noch robuster: Robuster Start: Befreit die Pumpe am Anfang der Heizsaison von Verunreinigungen. Sommermodus: Einstellung der Leistung der Pumpe im Sommer auf die wärmere Außentemperatur - für zusätzliche Energieeffizienz. Magnetitbeständigkeit: Stellt sicher, dass keine kleinen Metallteile in den wichtigen Teilen der Pumpe stecken bleiben, wenn sie magnetisiert sind. Trockenlaufschutz: Stellt sicher, dass die Pumpe niemals ohne Flüssigkeit im System läuft - hinzu kommt eine unübertroffene Energieeffizienz, einfache Installation und die Tatsache, dass ALPHA2 sowohl Ihre Heizanforderungen als auch bis zu 90 % Ihrer Klimaanforderungen abdeckt.Die GRUNDFOS ALPHA2 eignet sich für:Systeme mit konstantem oder variablem DurchflussEinrohrsystemeZweirohrsystemeFußbodenheizungWarmwasser-ZirkulationssystemeSysteme mit Nachtabsenkung erforderlichMerkmale und VorteileBessere Leistung bei marktführender Effizienz (EEI0.15) in einem kompakteren DesignNeuer Durchflussmesser zur Fehlerbehebung und zum AusgleichAUTOADAPT wählt beste Leistungskurve für Effizienz und KomfortInnovativer Stecker vereinfacht PumpenanschlussIsolierschalen enthalten.

ALPHA2 is able to withstand the tough conditions in a heating system, and with four newly added features, it just got even tougher:Robust start-up:Shakes free any impurities before the pump starts at the beginning of the heating season.Summer mode:Adjustment of the pump’s performance in the summer to the warmer temperature outside – giving customers extra energy efficiency.Magnetite resistance:Ensures that no small pieces of metal get stuck in the pump’s vital parts when they are magnetised.Dry-running protection:Makes sure the pump never runs without liquid in the system - add to that unrivalled energy efficiency, easy installation and the fact that ALPHA2 covers both your heating demands and up to 90 % of your air-conditioning and cooling demands.The GRUNDFOS ALPHA2 is suitable for:• Systems with constant or varying flow• One pipe systems• Two pipe systems• Underfloor-heating• Domestic hot-water recirculation• Systems where night setback is required.Features an

Produktname: Kabelhalterung für 2 Schwimmerschalter

Die hocheffiziente Coomfort PM-Serie ist ein Produkt für die Warmwasserzirkulation in Ein- und Zweifamilienhäusern. Der Motor ist ein einphasiger, 2-poliger, Hysterese-, Permanentmagnetmotor in Übereinstimmung mit der EMC-Richtlinie. Merkmale und Vorteile: * Einzigartige AUTOADAPT spart bis zu 50% Wärmeenergie und 87% Motorenergie im Vergleich zu einer Standardpumpe im Dauerbetrieb * Spülfunktion * Automatischer Legionellenbetrieb (falls vom System unterstützt) * Automatische Wochenend- und Urlaubsfunktion * Temperaturregelung optional* Dauerbetrieb optional* Schnelle und einfache elektrische Installation aufgrund des millionenfach bewährten ALPHA-Steckers* Leicht zu reinigender und kalkunempfindlicher sphärischer Rotor* Anwendungsbereich bis 14°dH Wasserhärte* Verschleißfreier Betrieb durch flüssigkeitsgeschmiertes Lager* Kein Leckagerisiko durch eine statische Dichtung.* Einfache Wartung und Reinigung durch leicht abnehmbaren Motorkopf, der auf alle Standard-Umwälzpumpengehäuse passt.* Korrosionsbeständiges Pumpengehäuse aus Messing.* Aufgrund des impedanzgeschützten Motors kein Motorschutz erforderlich.* Keine zusätzlichen Installationskosten aufgrund integrierter Rückschlagklappe und Absperrventil im Pumpengehäuse.Flüssigkeit:Flüssigkeitstemperaturbereich:2 .. 95 °CTechnisch:TF-Klasse:95Zulassungen auf Typenschild:VDE, GS, CEMaterialien:Pumpengehäuse:Messing MS 68Laufrad:Edelstahl, EPDM, PPO, PTFE, GraphitInstallation:Höchstdruckbetrieb:10 barRohranschluss:G 1 1/4Port-to-Port-Länge :110 mmElektrische Daten:max. Leistungsaufnahme :8 WRated voltage :1 x 230 VStrom in Geschwindigkeit 3 :0.07 AKondensatorgröße - Laufzeit :0.6 FSchutzart (IEC 34-5):IP44Isolationsklasse (IEC85):FOthers:Nettogewicht :1.35 kgBruttogewicht :1.51 kgVersandvolumen:0.003 m3

Alarmgerät mit Lampe und Hupe für Autoadapt

Unilift AP35.40.06.A1.VSubmersible drainage pump typeVertical single-stage stainless steel submersiblepump with vertical discharge port and integratedsubmersible 1-phase totally enclosed motorin insulation class F with thermal overloadprotection. The pump is fitted with suction strainer and level switch for automatic start and stop.The impeller is a VORTEX impeller for35 mm free passage suitable for pumpinggroundwater, surface water, rain water andsimilar.The pump has a double shaft seal and anintermediate oil chamber pre-filled with non-toxicspecial oil.The pump has a riser pipe, a cooling jacket for continuous cooling of the motor by the pumped liquid and long-life deep-groove greased-for-life ball bearings.The pump is ready for use as it is fitted withcarrying handle and is supplied with a10 m mains cable. The mains cable is ofthe plug type with glass sealing compound in thesocket to prevent penetration of humidity intothe stator windings.Liquid:Liquid temperature range:0 .. 55 °CTechnical:Type of impeller:VORTEXMaximum particle size:35 mmMaterials:Pump housing:Stainless steelPump housing:DIN W.-Nr. 1.4301Pump housing:AISI 304Impeller:Stainless steelImpeller:DIN W.-Nr. 1.4301Impeller:AISI 304Installation:Pump outlet:Rp 1 1/2Maximum installation depth:10 mElectrical data:Type of motor:PSCPower input - P1:0.9 kWRated voltage:1 x 230 VRated current:4 ACos phi - power factor:0,97Rated speed:2810 rpmCapacitor size - run:16 F/400 VEnclosure class (IEC 34-5):IP68Insulation class (IEC 85):FLength of cable:10 mType of cable plug SchukoOthers:Net weight:11.4 kgGross weight:11.9 kg

Unilift AP50B.50.11.3.VSubmersible effluent pumpVertical single-stage stainless steel submersiblepump with integrated submersible 3-phasemotor. The pump is fitted with ring stand and carryinghandle and is supplied with a 5 m mainscable. The impeller is a VORTEX impeller for50 mm free passage suitable for pumpingsurface water, groundwater, wastewater andsimilar.The pump has a double shaft seal and anintermediate oil chamber pre-filled with non-toxicspecial oil. The motor is insulation class F and has long-life deep-groove greased-for-life ball bearings.The pump has R 2' discharge port and is readyfor installation either free-standing or on anauto-coupling system. Liquid:Maximum liquid temperature:40 °CTechnical:Type of impeller:VORTEXMaximum particle size:50 mmMaterials:Pump housing:Stainless steelPump housing:DIN W.-Nr. 1.4301Pump housing:AISI 304Impeller:Stainless steelImpeller:DIN W.-Nr. 1.4301Impeller:AISI 304Installation:Pump outlet:R 2'Maximum installation depth:7 mElectrical data:Power input - P1:1.75 kWRated voltage:3 x 400 VRated current:2.81 ACos phi - power factor:0,90Rated speed:2785 rpmEnclosure class (IEC 34-5):IP68Insulation class (IEC 85):FLength of cable:5 mType of cable plug:NONEOthers:Net weight:10.6 kg

SOLOLIFT2 D-2Sololift2 D-2 is a small, compact automatic lifting station suitable for pumping of wastewater off places in private dwellings where greywater (w/o faeces) cannot be led directly to the sewer by means of a natural downward slope.Sololift2 D-2 is typically used for:• cabinet showers, washbasins or bidets in basements below sewer level, in connection with the renovation or modernisation of existing buildings, where the location may be remote from the main soil pipe so that a natural slope cannot be established.Extremely low switching levels for lowest construction heights, advantageously in case of connection of a shower receptor.Sololift2 D-2 is suitable for confined space conditions in built-in cabinets or also below shower receptors or pedestals.The pumping of liquids containing other material may cause faults and limit the scope of our guarantee.The compact lifting station is equipped with- Cable with or without plug (see technical data)- Disc

SOLOLIFT2 WC-1Sololift2 WC-1 is a small, compact automatic lifting station suitable for pumping of wastewater off places in private dwellings where wastewater cannot be led directly to the sewer by means of a natural downward slope.Sololift2 WC-1 is suitable for pumping wastewater from a toilet containing toilet paper and faeces with an additional connection on the lid for e.g. a washbasin.The pumping of liquids containing other material may cause faults and limit the scope of our guarantee.Sololift2 WC-1 is typically used to dewater:• toilet and washbasin in basements below sewer level, in connection with the renovation or modernisation of existing buildings, where the location may be remote from the main soil pipe so that a natural slope cannot be established.The compact lifting station is equipped with- Cable with or without plug (see technical data)- Horizontal or vertical fastening possibility of discharge hose connector with several adaptors for pipes wi

MAGNA3 40-100 FMAGNA3 – More than a pumpWith its unrivalled efficiency, all-encompassing range and built-in communication capabilities plus functionalities replacing system components, the MAGNA3 is ideal for engineers and specifiers looking to create high-performance systems for buildings. This pump in the Grundfos Master Class will fit both heating and cooling applications perfectly, making it the obvious choice for almost any building project – old or new.The MAGNA3 is of the canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid.The innovative clamp with only one screw enables easy repositioning of the pump head. The MAGNA3 is a pump with no maintenance requirements and with extremely low Life Cycle Cost.The pump is characterised by the following:• controller integrated in the control box• control panel with TFT display on the control box• control box prepared for optional CIM modules• built-in differential-pressure and temperature sensor• cast-iron pump housing (depending on model)• carbon-fibre-reinforced composite rotor can• stainless-steel bearing plate and rotor cladding• aluminium alloy stator housing• air-cooled power electronicsThe MAGNA3 is a single-phase pump.Characteristic features• AUTOADAPT.• FLOWADAPT and FLOWLIMIT (more than a pump function as it reduces the need for pump throttling valves).• Proportional-pressure control.• Constant-pressure control.• Constant-temperature control.• Constant-curve duty.• Max. or min. curve duty.• Automatic Night Setback.• No external motor protection required.• Insulating shells supplied with single-head pumps for heating systems.• Large temperature range where the liquid temperature and the ambient temperature are independent of each other.CommunicationThe MAGNA3 enables communication via the following:• wireless Grundfos GO Remot

Die Premium-Wahl, wenn die Systemsteuerung und Überwachung entscheidend sind. Die MAGNA3 unterstützt Feldbus durch optionale CIM-Module und verfügt über ein TFT-Display zur intuitiven Konfiguration der intelligenten Funktionen. Anwendungen: Heizung, Klimatisierung, Pumpendesigns: Dosenrotor Technische Daten: Maximaler Kopf: 18,88 m Flüssigkeitstemperatur: -10 .. 110 ° C Maximaler Durchfluss: 76,6 m3 / h P max : 16 bar

MAGNA3 40-100 FMAGNA3 – More than a pumpWith its unrivalled efficiency, all-encompassing range and built-in communication capabilities plus functionalities replacing system components, the MAGNA3 is ideal for engineers and specifiers looking to create high-performance systems for buildings. This pump in the Grundfos Master Class will fit both heating and cooling applications perfectly, making it the obvious choice for almost any building project – old or new.The MAGNA3 is of the canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid.The innovative clamp with only one screw enables easy repositioning of the pump head. The MAGNA3 is a pump with no maintenance requirements and with extremely low Life Cycle Cost.The pump is characterised by the following:• controller integrated in the control box• control panel with TFT display on the control box• control box prepared for optional CIM modules• built-in differential-pressure and temperature sensor• cast-iron pump housing (depending on model)• carbon-fibre-reinforced composite rotor can• stainless-steel bearing plate and rotor cladding• aluminium alloy stator housing• air-cooled power electronicsThe MAGNA3 is a single-phase pump.Characteristic features• AUTOADAPT.• FLOWADAPT and FLOWLIMIT (more than a pump function as it reduces the need for pump throttling valves).• Proportional-pressure control.• Constant-pressure control.• Constant-temperature control.• Constant-curve duty.• Max. or min. curve duty.• Automatic Night Setback.• No external motor protection required.• Insulating shells supplied with single-head pumps for heating systems.• Large temperature range where the liquid temperature and the ambient temperature are independent of each other.CommunicationThe MAGNA3 enables communication via the following:• wireless Grundfos GO Remot

MAGNA3 32-120 FMAGNA3 – More than a pumpWith its unrivalled efficiency, all-encompassing range and built-in communication capabilities plus functionalities replacing system components, the MAGNA3 is ideal for engineers and specifiers looking to create high-performance systems for buildings. This pump in the Grundfos Master Class will fit both heating and cooling applications perfectly, making it the obvious choice for almost any building project – old or new.The MAGNA3 is of the canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid.The innovative clamp with only one screw enables easy repositioning of the pump head. The MAGNA3 is a pump with no maintenance requirements and with extremely low Life Cycle Cost.The pump is characterised by the following:• controller integrated in the control box• control panel with TFT display on the control box• control box prepared for optional CIM modules• built-in differential-pressure and temperature sensor• cast-iron pump housing (depending on model)• carbon-fibre-reinforced composite rotor can• stainless-steel bearing plate and rotor cladding• aluminium alloy stator housing• air-cooled power electronicsThe MAGNA3 is a single-phase pump.Characteristic features• AUTOADAPT.• FLOWADAPT and FLOWLIMIT (more than a pump function as it reduces the need for pump throttling valves).• Proportional-pressure control.• Constant-pressure control.• Constant-temperature control.• Constant-curve duty.• Max. or min. curve duty.• Automatic Night Setback.• No external motor protection required.• Insulating shells supplied with single-head pumps for heating systems.• Large temperature range where the liquid temperature and the ambient temperature are independent of each other.CommunicationThe MAGNA3 enables communication via the following:• wireless Grundfos GO Remot

ALPHA2 is able to withstand the tough conditions in a heating system, and with four newly added features, it just got even tougher:Robust start-up:Shakes free any impurities before the pump starts at the beginning of the heating season.Summer mode:Adjustment of the pump’s performance in the summer to the warmer temperature outside – giving customers extra energy efficiency.Magnetite resistance:Ensures that no small pieces of metal get stuck in the pump’s vital parts when they are magnetised.Dry-running protection:Makes sure the pump never runs without liquid in the system - add to that unrivalled energy efficiency, easy installation and the fact that ALPHA2 covers both your heating demands and up to 90 % of your air-conditioning and cooling demands.The GRUNDFOS ALPHA2 is suitable for:• Systems with constant or varying flow• One pipe systems• Two pipe systems• Underfloor-heating• Domestic hot-water recirculation• Systems where night setback is required.Features and benefits• Better performance with market leading efficiency (EEI0.15) in a more compact design• New flow meter for trouble-shooting and balancing• AUTOADAPT selects best performance curve for efficiency and comfort• Innovative plug simplifies pump connection• Insulation shells included.

Unilift KP 350 A 1Submersible drainage pumpVertical single-stage stainless steel submersiblepump with vertical discharge port and integratedsubmersible 1-phase canned motor ininsulation class F with thermal overloadprotection. The pump is fitted with suction strainer and acarrying handle and is supplied with a 10 mmains cable and float switch for automatic startand stop.The impeller is a semi-open impeller for 10 mmfree passage suitable for pumping groundwater,surface water, rain water and similar liquids.The pump has a double shaft seal consisting oftwo lip seals with grease in-between.The pump has an outer casing ensuring continuouscooling of the motor by the pumped liquid.The rotor shaft operates in two maintenance-freecarbon bearings cooled by the pumped liquid.The motor is filled with a non-toxic motor liquid. Liquid:Liquid temperature range:0 .. 50 °CTechnical:Maximum particle size:10 mmMaterials:Pump housing:Stainless steelPump housing:DIN W.-Nr. 1.4301Pump housing:AISI 304Impeller:Stainless steelImpeller:DIN W.-Nr. 1.4031Impeller:AISI 304Installation:Pump outlet:Rp 1 1/4Maximum installation depth:10 mElectrical data:Power input - P1:700 WRated voltage:1 x 220-240 VRated current:3.2 ACapacitor size - run:8 F/400 VEnclosure class (IEC 34-5):IP68Insulation class (IEC 85):FLength of cable:10 mType of cable plug: SchukoOthers:Net weight:8 kgGross weight:8.3 kgShipping volume:0.013 m3