Fluke – Test- und Messgeräte

VoltAlertTM technology for non-contact voltage detectionAutoVolt automatic AC/DC voltage selectionLow input impedance: helps prevent false readings due to ghost voltageLarge white LED backlight to work in poorly lit areasTrue RMS for accurate measurements on non-linear loadsMeasures 10 A (20 A overload for 30-seconds)Resistance, continuity, frequency and capacitanceMin/Max/Average with elapsed time to record signal fluctuationsCompact ergonomic design for one-handed operationCompatible with optional magnetic hanger (ToolPakTM) for hands free operationCAT III 600 V safety ratedIncludes:4 mm silicone test lead setHolsterUser manual

Patented TwistGuardTM extendable tip shroud meets the highest electrical safety requirements to reduce tip exposure while providing the versatility needed for most measurementsNew WearGuardTM lead wire wear indication. Each test lead is covered by two layers of silicone insulation, inner contrasting color is exposed when the leads are nicked, scuffed, or otherwise damaged and in need of replacementDouble insulated silicone leads. TL175 test leads withstand high temperatures and remain flexible in cold temperatures.Extra-heavy duty strain relief on both probe-end and plug-end, tested beyond 30,000 bends without failure.Universal input plugs are compatible with all instruments that accept standard 4 mm shrouded banana plugsRatings: CAT II 1000 V, CAT III 1000 V, CAT IV 600 V, 10 A max., Pollution Degree 2TL175E also available. Includes removable 4 mm lantern tips that thread onto the lead tipProbes always show correct category rating for tip being usedEnvironmental ratings: -20 °C to 55 °C (-4 °F to 131 °F), altitude: 2000 m (6,562 ft)Conforms to EN61010-031

Netzwerktester-Set

Always on for faster, safer voltage testing2AC is the latest addition to the VoltAlertTM ac non- contact voltage tester family from Fluke and is designed to be pocket-sized and easy to use. The 2AC tests for energized circuits and defective grounds, whether it’s for an electrician on the factory floor or the do-it-yourselfer around the house. The tip of the pocket-sized tester will glow red when within close proximity of an outlet, terminal strip, or power cord where voltage is present.Voltage detection from 200 to 1000 V ac, suitable for a wide range of residential, commercial and industrial needs.NEW! Always on, using special low power circuitry to sustain battery life and ensure your 2AC is always ready.NEW! Innovative ‘Battery Check’ button function ensures battery is in good condition*Category IV – 1000 V overvoltage rated product for best in class user protectionIntegrated clip design, optimized for pocket storagePowered by 2x AAA batteries (included)Fluke ruggedness and reliability

Non-contact AC voltage detector and LED flashlight combined into one easy to use pen-style design. The LVD2 is a CAT IV 600 V rated non-contact detector that is suitable for commercial and industrial applications. The LVD2 includes dual sensitivity turning blue 1" to 5" (2.54 cm to 12.7 cm) from the source and red when at the source.Dual SensitivityLED light with 100,000 hour lifeDetects from 90 to 600 V ACRated to CAT IV 600 VDual Levels of DetectionBlue indicates proximity to AC Voltage sourceRed indicates you’re at the sourceOperating temperature 0 deg C to 50 deg CUltra-Bright White LED100,000 hr bulbAAA battery included

The TL75 Hard PointTM Test Lead Set offers the convenience of a test lead and probe-in-one unit with a variety of connections. One pair (red, black) comfort grip probe with PVC insulated right angel shrouded 4mm (0.16) banana plugs

Geben Sie Ihren Fluke-Werkzeugen den Schutz, den sie verdienen. Sie haben das Beste gekauft, warum schützen Sie es nicht mit Fluke-Gehäusen? Das C25-Tragegehäuse ist ein strapazierfähiges, mit Reißverschluss versehenes Tragegehäuse mit Polsterung und Innentasche sowie hochwertigem Polyester-Exterieur. Es enthält einen praktischen Handriemen und trägt die meisten beliebten digitalen Multimeter von Fluke. Unser bisher meistverkauftes Gehäuse! Jetzt in Standard- und Tarnfarben erhältlich Abmessungen (HxBxT) 218 mm x 128 mm x 64mm

Better than a test probe alone – these two inch long rigid back probe pins easily pass between the weather pack seal and wire. A sharp point ensures good contact to the electrical connector, and the pin’s insulation protects it from shorting to other wires.Slides onto test probes measuring 2 mm (0.08 inches)Tested to 60 V DC

The Fluke 113 Digital Multimeter gives users the means to quickly and easily do basic meter set and reconnect testing. This meter is simple-to-use and has the features needed to repair most electrical problems. The Fluke 113 has significant improvements over other digital multimeters available on the market, including Fluke model 7-600. Using the Fluke VCHEKTM LoZ low impedance measurement function, users can simultaneously test for voltage or continuity. The Min/Max function lets you record signal fluctuations. The Fluke 113 can perform diode tests, and also provides both auto and manual ranging capabilities. With features such as conformance to the latest safety standards, backlight, and a much larger display that’s easier to view, this meter is a must have for every toolbox.Resources:VCHEKTM LoZ low impedance measurement function to simultaneously test for voltage or continuityTrue RMS for accurate AC measurements on non-linear loadsA large backlit display allows for easy visibility in low-lit areasRecord signal fluctuations using the Min/Max functionDiode test for testing general-purpose germanium, silicon, and power diodesIntegral holster with probe holders for easy storageAuto and Manual ranging for added user functionalityMeets Measurement Category CAT III 600 V and Category IV 300 V standards for a higher level of safetyThe optional TPAK magnetic hanger allows the user hands-free flexibility

Fluke’s two-pole voltage and continuity testers are built to work the way you work. They give you the best combination of safety, ease-of-use and fast answers available anywhere.CAT IV 600 V, Cat III 690 V safety rating Fluke’s family of Two-Pole Voltage testers comply with both regulation HSE GS 38 (tip caps) and IEC EN 61243-3: 2010.4 ways to detect ac/dc voltage A clear, instantly visible LED indicator, a bright digital display of the measurement value, an audible continuity test, and vibration to give tactile feedback (vibration indicator on T110, T130, T150).Backlit graduated scale and backlit indicatorsVibration provides tactile feedback (T110, T130, T150).Audio on/off for testing in quiet areas.Low battery indicatorDetects voltage even with discharged batteriesImproved probe docking for secure storagePhase rotation indicator for 3-phase systemsRCD functionality Two-button controls allow you to draw more current from the circuit under test and intentionally trip Residual-Current Devices (RCDs) remotelyDisplay Hold (T130, T150)Built in electric torch (T110, T130, T150)Single-phase voltage offers fast identification of live conductorsPush-on probe tips, probe tip protector and storage accessoryProbe tip protector and storage accessory Tip protector serves as an extra hand when opening UK electrical safety outlets.Resistance testing to 1999 ohms (T150)WearGuardTM insulation shows damage to test leads

The Fluke T5 Electrical Testers let you check voltage, continuity and current with one compact tool. With the T5, all you have to do is select volts, ohms, or current and the tester does the rest. OpenJawTM current lets you check current up to 100A - without breaking the circuit. Its tough test leads stow neatly in the back of the tester, making it easy to tote the T5 in your tool pouch. Detachable SlimReachTM test probes are customized for national electrical standards. The test leads accept optional accessories such as clips and specialty probes. The optional H5 holster lets you clip the T5 onto your belt. Available in 600V and 1000V models.1000V Voltage, Continuity and Current TesterAll models include:4 mm detachable probesInstruction sheet

Designed to Identify Complex Signal Problems FastWhen productivity is on the line and you need to solve problems fast, the Fluke 87V delivers the accuracy and advanced troubleshooting capabilities you need. Designed specifically to handle complex signals, the 87V industrial multimeter, allows you to gain productivity by taking the guesswork out of drive system troubleshooting even in loud, high energy, and high altitude locationsSpecificationsVoltage DCMaximum voltage1000 VAccuracy±(0.05% + 1)Maximum resolution10 VVoltage ACMaximum voltage1000 VAccuracy±(0.7% + 2) True RMSAC bandwidth20 kHz with low pass filter, 3 db @ 1 kHzMaximum resolution0.1 mVCurrent DCMaximum amps10 A (20 A for 30 seconds maximum)Amps accuracy±(0.2% + 2)Maximum resolution0.01 ACurrent ACMaximum amps10 A (20 A for 30 seconds maximum)Amps accuracy±(1.0% + 2) True RMSMaximum resolution0.1 AResistanceMaximum resistance50 MAccuracy±(0.2% + 1)Maximum resolution0.1 CapacitanceMaximum capacitance9,999 Faccuracy±(1% + 2)Maximum resolution0.01 nFFrequencyMaximum frequency200 kHzAccuracy±(0.005% + 1)Maximum resolution0.01 HzDuty cycleMaximum duty cycle99.9%Accuracy±(0.2% per khz + 0.1%)Maximum resolution0.1%Temperature measurement–200.0°C – 1090°C–328.0°F – 1994.0°Fexcluding probe80 BK temperature probe–40.0°C – 260°C–40.0°F – 500°F, 2.2°C or 2% whichever is greaterConductanceMaximum conductance60.00 nSAccuracy±(1.0% + 10)Maximum resolution0.01 nSDiodeRange3 VResolution1 mVAccuracy±(2% + 1)Duty cycle rangeAccuracyWithin ±(0.2% per kHz + 0.1%)Environmental SpecificationsOperating temperature–20°C to + 55°CStorage temperature–40°C to + 60°CHumidity (without condensation)0% – 90% (0°C – 35°C)0% – 70% (35°C – 55°C)Operating Altitude2000 mSafety SpecificationsOvervoltage categoryEN 61010–1 to 1000 V CAT III, 600V CAT IVAgency approvalsUL, CSA, TUV, VDE listedMechanical and General SpecificationsSize201

Einstellbare Spitzenlänge für erhöhte Sicherheit und Präzision. Kompatibel mit den Testleitungen der TL22x-Serie, TL238 und TL27. Entspricht EN61010-031 CAT II 1000 V, CAT III 1000 V, CAT IV 600, Bewertung von 10 A UL-Listung Einjährige Garantie Das patentierte TwistGuardTM ausziehbare Spitzengehäuse erfüllt die höchsten elektrischen Sicherheitsanforderungen zur Reduzierung der Spitzenbelichtung und bietet gleichzeitig die Vielseitigkeit für die meisten Messungen Bewertungen: CAT II 1000 V, CAT III 1000 V , KATZE IV 600V, max. Stromstärke von bis zu zehn Ampere (10 A), Verschmutzungsgrad zwei Die Sonden zeigen immer die korrekte Kategoriebewertung für den verwendeten Tipp an Umweltbewertungen: -20 ° C bis +55 ° C (-4 ° F bis +131 ° F), Höhe: 2000 m (6562 ft) Entspricht EN61010-031 Einjährige Garantie Bewertungen: KATZE II 1.000 V; KATZE III 1.000 V; KATZE IV 600 V; maximaler Strom von zehn Ampere (10 A); Verschmutzungsgrad zwei Länge der freiliegenden Sondenspitze: Von19 mm auf4 mm einstellbar (-75 Zoll auf -16 Zoll) Umweltbewertungen:-20°Cbis+55°C(-4°Fbis+131°F),Höhe:2000m(6562ft) TL175 und TL175E sind ebenfalls erhältlich. TL175E enthält abnehmbare 4-mm-Laternenspitzen, die auf die Leiterspitze geschraubt werden können. Entspricht EN61010-031

Sicherung 803293 - 11A - 1000V - 20kA - 10,3x38,1

Große weiße LED-Hintergrundbeleuchtung für die Arbeit in schlecht beleuchteten Bereichen. Widerstand und Kontinuität. Frequenz und Kapazität. Maximale Spannung AC/DC 600V. Strommessung AC/DC 10A (20 A Überlastung für maximal 30 Sekunden). Min/Max/Durchschnitt zur Aufzeichnung von Signalfluktuationen. CAT III 600 V Sicherheitsbewertung, Konformität mit Sicherheitsvorschriften, alle Eingänge sind CE-, IEN61010-1 CAT III 600V-geschützt, UL-, CSA-, TUV-gelistet und VDE-zertifiziert.Enthält: Holster, installierte 9V-Batterie, Silikonprüfleitung mit einem Durchmesser von 4 mm und Benutzerhandbuch

Ersatz-Testleitungen für T5

Test leads are an integral part of the complete measurement system and extend the capabilities of your digital multimeter. The TL224 SureGripTM Insulated Test leads offer reinforced strain relief and includes banana jack termination for a variety of test lead configurations. SureGripTM accessories are designed to improve steadiness in slippery hands. Rubber over molded surfaces and finger-hugging curves give the user a comfortable, reliable grip on the accessory so they can focus on making an accurate measurement.DMM test leads (red, black) with safety shrouded, standard diameter banana plugsRight angle connector on one end and straight connector on the otherReinforced strain relief1.5 meter silicone-insulated wire resists heat & coldCAT IV 600 V, CAT III 1000 V, 10 A rating. UL listed

Fluke 4111533 Nicht kategorisiert

SpecificationsVoltage DCAccuracy1±(0.09% + 2)Max. resolution0.1 mVMaximum1000 VVoltage ACAccuracy1±(1.0% + 3)Max. resolution0.1 mVMaximum1000 VCurrent DCAccuracy1±(1.0% + 3)Max. resolution0.01 mAMaximum10 ACurrent ACAccuracy1±(1.5% + 3)Max. resolution0.01 mAMaximum10 AResistanceAccuracy1±(0.9% + 1)Max. resolution0.1 Maximum50 MCapacitanceAccuracy1±(1.2% + 2)Max. resolution1 nFMaximum10,000 FFrequencyAccuracy1±(0.1% + 1)Max. resolution0.01 HzMaximum100 kHzTemperatureAccuracy1±(1.0% + 10)Max. resolution0.1°CRange-40°C / 400°CIncludes:80BK Temperature ProbeInstalled 9V batteryTest leadsUsers manual

Ein Paar (rot, schwarz) schlanker Sondenkörper zum Prüfen eng beieinander liegender oder versenkter Anschlüsse. Harte Edelstahl-Sondenspitzen. Flachblatt-Design zur sicheren Verwendung in Steckdosen mit Klingenkontakt. CAT II 1000 V, 10 A Bewertung EN/IEC 61010-031:2002 +A1:2008

fuse440mA(F), 1000V, 10kA,

Die Fluke T5 Electrical Testers ermöglichen es Ihnen, Spannung, Kontinuität und Strom mit einem kompakten Werkzeug zu überprüfen. Mit dem T5 müssen Sie nur Volt, Ohm oder Strom auswählen und der Tester erledigt den Rest. OpenJawTM-Strom ermöglicht es Ihnen, Ströme bis zu 100A zu prüfen - ohne den Stromkreis zu unterbrechen. Die robusten Prüfleitungen lassen sich ordentlich im hinteren Teil des Testers verstauen und erleichtern so das Transportieren des T5 in Ihrer Werkzeugtasche. Abnehmbare SlimReachTM-Testsonden sind an nationale elektrische Standards angepasst. Die Prüfleitungen akzeptieren optionales Zubehör wie Clips und Spezialsonden. Der optionale H5-Holster ermöglicht es Ihnen, den T5 an Ihrem Gürtel zu befestigen.Spannungsprüfer enthält: 600V Spannungs-, Kontinuitäts- und Stromtester4 mm abnehmbare SondenAnleitung

Now compatible with Fluke ConnectTM Mobile App The 289 is the next generation high performance industrial logging multimeter designed to solve complex problems in electronics, plant automation, power distribution, and electro-mechanical equipment. With the ability to log data and review it graphically on-screen, you can solve problems faster and help minimize downtime. Let the new 289 be your watchdog for systems or processes while you are off doing other jobs. Now communicate wirelessly with your iOS and Android smart devices with the Fluke Connect mobile app and ir3000 FC wireless connector (sold separately).NEW – Let your team see what you see in an instant with ShareLiveTM video call (requires Fluke Connect mobile app and ir3000 FC wireless connector).TrendCapture graphically displays logged data session to quickly determine whether anomalies may have occurred.Zoom on trend provides unprecedented ability to view and analyze TrendCapture data, zoom in up to 14 times.Selectable AC filter (smoothing mode) helps display a steadier reading when the input signal is changing rapidly or noisy.Adjustable recording and auto hold thresholds, specify a percentage change in the readings that begins a new event.Large 50,000 count, 1/4 VGA dot matrix display with white backlight.Logging function with expanded memory for unattended monitoring of signals over time. Using on-board TrendCapture users can graphically review logged readings without needing a PC. Store up to 15,000 recorded events.Save multiple logging sessions before PC download is necessary.Two terminal 50 ohm range with 1 milliohm resolution, 10 mA source current. Useful for measuring and comparing differences in motor winding resistance or contact resistance.Low Pass filter for accurate voltage and frequency measurements at the same time on adjustable speed motor drives and other electrically noisy equipment.LoZ Volts. Low impedance voltage function for eliminating ghost voltages. Also recommended when

SpezifikationenSpannung DCGenauigkeit1±(0,09% + 2)Max. Auflösung0,1 mVMaximum1000 VSpannung ACGenauigkeit1±(1,0% + 3)Max. Auflösung0,1 mVMaximum1000 VStrom DCGenauigkeit1±(1,0% + 3)Max. Auflösung0,01 mAMaximum10 AStrom ACGenauigkeit1±(1,5% + 3)Max. Auflösung0,01 mAMaximum10 AWiderstandGenauigkeit1±(0,9% + 2)Max. Auflösung50 MCapacitanceAccuracy11 nFMaximum10 000 FFrequenzGenauigkeit11 HzMaximum100 kHzEnthält:Eingebaute 9-V-BatterieTestleitungenBenutzerhandbuch

Ein Paar (rot, schwarz) schlanker Sondenkörper zum Prüfen eng beieinander liegender oder versenkter Anschlüsse. Harte Edelstahl-Sondenspitzen mit einem Durchmesser von 2 mm für Elektronikarbeiten. CAT II 1000 V, 10 A Bewertung