Viega Druckrohre und Armaturen - Seite 21

Viega 2217.2

Viega 1165

Viega 1117.2

Prestabo T-piece with SC-Contur- galvanised non-alloyed steel- press connectorsComponentsEPDM sealing elements, VdS certificationd1: 54, d2: 22, d3: 54

Viega 1118

Sanpress Plug-in piece- gunmetal or silicium bronze- plug-in end, R-threadComponentsPolygon.

Sanpress Plug-in piece- gunmetal or silicium bronze- plug-in end, R-threadComponentsPolygon.

Prestabo T-piece with SC-Contur- non-alloyed steel, galvanised- press connections, Rp-threadComponentsEPDM sealing elements, polygon

Press connector system with press connectors and pipes made of copper in acc. with EN 1057 and DVGW worksheet GW 392 suitable for:•Gases in acc. with DVGW G 260 in gas installations in acc. with DVGW-TRGI 2008 (DVGW worksheet G 600) / DVFG-TRF 2012•Liquid gas in the gas phase for domestic and commercial applications, tested in acc. with DVGW worksheet G 5614•Heating oil pipelines for heating oil in acc. with DIN 51603-1•Diesel fuel pipelines for diesel fuel, as suction and pressure pipelines in acc. with EN 590 in consideration of the general technical approval Z-38.4-71Press connectorsAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet G 5614, point 4.4.1, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingYellow dot, yellow rectangle and inscription »Gas MOP 5 / GT1«Sealing elementsHNBR, yellowDimensions/MaterialStandard sizes: d 12, 15, 18, 22, 28, 35, 42, 54 made of copperXL sizes: d 64.0 made of copperPress connectors with threaded connection d 12–54 made of gunmetalXL press connectors with threaded connection d 64.0 made of copperAreas of applicationNatural gas/Liquid gasHeating oil/Diesel fuel (d 12–54)NoteOnly Viega copper and gunmetal press connectors, which are marked with a yellow rectangle and have the inscription »Gas MOP 5 / GT1« are permitted for use in installations for gas, heating oil and diesel fuel systems!Use of the system for application areas and media other than those described here must be agreed with Viega Service Center through a material request.Operating conditionsGas and liquid gas systems•Operating temperature -20 °C up to +70 °C•Operating pressure max. 0.5 MPa•Operatin

Prestabo Crossover galvanised non-alloyed steel plug-in ends Galvanised non-alloyed steel plug-in ends

Viega 2426

Viega 2212

Press connector system with press connectors made of copper and gunmetal tested in acc. with DVGW worksheet W 534 with DVGW test seal and pipes made of copper in acc. with EN 1057 in acc. with DVGW worksheet GW 392.Suitable for drinking water installations in acc. with DIN 1988.For dimensionally stable concealed and pre-wall installations of manifold and riser pipes in Viega component assembly.Press connectorsAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionSealing elementsEPDM, black (ethylene-propylene-dien-monomer rubber), up to 110 °C

Viega 2226

Sanpress Inox Sliding coupling with SC-Contur- steel non-corroding- press connectorsComponentsEPDM sealing elementsd: 42(VdS certification)

Viega 2211.1

Viega 1118

Viega 2317.2

Sanpress Inox T-piece with SC-Contur- steel non-corroding- press connectors, Rp-threadComponentsEPDM sealing elements, polygon, VdS certificationd1: 22, Rp: 34, d2: 22

Sanpress Inox T-Stück mit SC-Contur- Stahl nicht korrodierend - PressverbindernKomponentenEPDM-Dichtelemente, VdS-Zertifizierungd1: 42, d2: 35, d3: 42

Sanpress Inox Adapter elbow 90° with SC-Contur- steel non-corroding- press connection, R-threadComponentsEPDM sealing element, polygond: 18, R: 34

Viega 2426.1

Viega 2416

Viega 2212.1

Viega 2211