Alu pex Systeme - Seite 19

Uponor 1070520 Sanitärarmatur Armaturenanschluss

Uponor 1070521 Sanitärarmatur Armaturenanschluss

Uponor 1029126 Sanitärarmatur Armaturenanschluss

Press coupling for DHW and radiator systems. PPSU plastic with stainless steel/aluminum press cap, guaranteed leaking if not pressed. Calibration-free. Only to be used with Uponor MLC tubes and with Uponor approved pressing tools.

Uponor 1029146 Sanitärarmatur Endzufuhr-Reduzierer

Used with Roth alu-laserplus pipe and Roth tools

Geberit Mepla T-Stück, gleich: d=16mm

Geberit Mepla Bogenadapter 90° mit männlichem Gewinde: d=20mm, R=3/4

Geberit Mepla T-piece, reduced: d=26mm, d1=16mm, d2=26mm

Geberit Mepla Reduzierstück: d=26mm, d1=16mm

Geberit Mepla T-piece, reduced: d=32mm, d1=16mm, d2=32mm

Geberit Mepla Kupplung: d=16mm

Geberit Mepla Reduzierstück: d=40mm, d1=26mm

Geberit Mepla T-piece, reduced: d=26mm, d1=20mm, d2=20mm

Geberit Mepla Verbindung für Eurokonus: d = 16mm, G = 3/4

Henco 50 x 50 mm PVDF Pressbogen 90° für Wasser-, Heiz- und Kühlanlagen. Max. 16 bar.

Geberit Mepla T-piece, reduced: d=32mm, d1=20mm, d2=32mm

Geberit Mepla T-Stück 32 x 26 x 26 mm

Geberit Mepla T-piece, reduced: d=20mm, d1=26mm, d2=20mm

Geberit Mepla Adapter mit männlichem Gewinde: d=16mm, R=1/2

Geberit Mepla connection nipple for manifold, for Euro cone: d=20mm, G=3/4

Henco 63 x 50 x 63 mm PVDF press tee for water-, heating- and cooling installations. Max. 16 bar.

Raxofix Coupling with SC-Contur- silicium bronze- press connectiond1: 32, d2: 25

Raxofix Adapter elbow 90° with SC-Contur- silicium bronze- press connection, R-threadd: 20, R: 34

Flow-optimised press connector system for drinking water installations in acc. with DIN 1988 and DIN 50930-6 as well as heating installations, tested in acc. with DVGW worksheet W 534.Press connectorsSafe and fast processing without calibration of the pipe ends through O-ring-free press technology in all dimensions. In this way, widening or calibration of the pipe-ends becomes superfluous and reduces the assembly times. The interaction between aerodynamic radii and minimal cross-section narrowings ensure the lowest pressure losses in press systems for multilayer pipes. This allows a smaller dimensioning of drinking water installations and reduces the pipeline volume.SC-ConturAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionPipesRaxofix PE-Xc/Al/PE-Xc•dimensionally stable, oxygen-proof in acc. with DIN 4726, greyRaxofix PE-Xc•flexible, blackDimensionsPress connectors and pipes•Raxofix-PE-Xc/Al/PE-Xc: d 16/20/25/32/40/50/63•Raxofix PE-Xc: d 16/20Areas of application PE-Xc/Al/PE-XcDrinking waterHeatingRainwaterCompressed airAreas of application PE-XcRainwaterDrinking waterUse of the system for application areas other than those described here must be agreed with Viega Service Center.Operating conditionsDrinking water installations•Operating temperature max. 70 °C•Operating pressure max. 1.0 MPaHeating installations•Operating temperature max. 80 °C•Operating pressure max. 1.0 MPaIrrelevant of the direction of flow, mixed installations are permitted.NoteThe DVGW test mark is only valid f