Alu pex Systeme - Seite 13

Geberit Mepla T-Stück, gleich: d=32mm

Prestee PPSU Uponor 20X16X16 mm

Geberit Mepla Bogenadapter 90° mit Innengewinde: d=20mm, Rp=1/2

PPSU-Kupplung Uponor 25 mm

PPSU-Kupplung Uponor 20X16 mm

Pressfittings für Fußbodenheizung, Trinkwasser- und Heizkörpersysteme. Kann nur mit Uponor MLCP-Rohren und Uponor-zugelassenen Presswerkzeugen verwendet werden. Aus Kunststoff gefertigt. Reduzierstück.

Prestee PPSU Uponor 40X32X40 mm

Prestee PPSU Uponor 40 x 25 x 40 mm (Maß eines Sanitäranschlusses aus Polyphenylsulfon-Material der Marke Prestee und hergestellt von Uponor)

PPSU-Kupplung Uponor 32X25 mm

Geberit Mepla Ellbogen: 90°, d=16mm

PPSU-Kupplung Uponor 25X20 mm

Presskupplung für Trinkwasser- und Heizkörpersysteme. PPSU-Kunststoff mit Edelstahl-/Aluminium-Presskappe, undicht, wenn nicht gepresst. Kalibrierungsfrei. Nur mit Uponor MLC-Rohren und von Uponor zugelassenen Presswerkzeugen zu verwenden.

Press coupling for DHW and radiator systems. PPSU plastic with stainless steel/aluminum press cap, guaranteed leaking if not pressed. Calibration-free. Only to be used with Uponor MLC tubes and with Uponor approved pressing tools.

Raxofix T-Stück mit SC-Contur- Siliziumbronze-Pressverbindern d1: 25, d2: 16, d3: 20

PPSU-Bogen Uponor 90° 40X40 mm

Prestee PPSU Uponor 16 x 20 x 16 mm (Maßeinheit für Rohr oder Fitting)

Raxofix T-Stück mit SC-Contur- Siliciumbronze-Pressverbindern d1: 20, d2: 20, d3: 16

Raxofix Adapter Ellbogen 90° mit SC-Contur-Siliciumbronze-Presseanschluss, Rp-Gewinde: 25, Rp: 34

Raxofix Verbindungsschraubfitting mit SC-Contur- Siliziumbronze- Pressanschluss, G-Gewinde- Flachdichtungskomponenten EPDM-Dichtelement d: 16, G: 34

Raxofix Adapter Ellbogen 90° mit SC-Contur-Siliciumbronze-Presseanschluss, Rp-Gewinde: 20, Rp: 34

Uponor PPSU Bogen 90° mit einem Durchmesser von 16mm.

Raxofix T-Stück mit SC-Contur-Siliciumbronze-Presseanschlüssen, Rp-Gewinde d1: 16, Rp: 12, d2: 16

Raxofix T-Stück mit SC-Contur-Siliciumbronze-Presseanschlüssen, Rp-Gewinde d1: 20, Rp: 12, d2: 20

Raxofix Adapter mit SC-Contur-Siliziumbronze-Pressanschluss, R-Gewinde: 16, R: 12

Flow-optimised press connector system for drinking water installations in acc. with DIN 1988 and DIN 50930-6 as well as heating installations, tested in acc. with DVGW worksheet W 534.Press connectorsSafe and fast processing without calibration of the pipe ends through O-ring-free press technology in all dimensions. In this way, widening or calibration of the pipe-ends becomes superfluous and reduces the assembly times. The interaction between aerodynamic radii and minimal cross-section narrowings ensure the lowest pressure losses in press systems for multilayer pipes. This allows a smaller dimensioning of drinking water installations and reduces the pipeline volume.SC-ConturAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionPipesRaxofix PE-Xc/Al/PE-Xc•dimensionally stable, oxygen-proof in acc. with DIN 4726, greyRaxofix PE-Xc•flexible, blackDimensionsPress connectors and pipes•Raxofix-PE-Xc/Al/PE-Xc: d 16/20/25/32/40/50/63•Raxofix PE-Xc: d 16/20Areas of application PE-Xc/Al/PE-XcDrinking waterHeatingRainwaterCompressed airAreas of application PE-XcRainwaterDrinking waterUse of the system for application areas other than those described here must be agreed with Viega Service Center.Operating conditionsDrinking water installations•Operating temperature max. 70 °C•Operating pressure max. 1.0 MPaHeating installations•Operating temperature max. 80 °C•Operating pressure max. 1.0 MPaIrrelevant of the direction of flow, mixed installations are permitted.NoteThe DVGW test mark is only valid f